| Usage: | Small-sized LCM |
|---|---|
| Touch Screen Type: | Capacitive |
| Type: | Color |
| Samples: |
|---|
| Customization: |
|---|
|
Shipping Cost:
Estimated freight per unit. |
about shipping cost and estimated delivery time. |
|---|
| Payment Method: |
|
|---|---|
| Initial Payment Full Payment |
| Currency: | US$ |
|---|
| Return&refunds: | You can apply for a refund up to 30 days after receipt of the products. |
|---|
Suppliers with verified business licenses
Audited Supplier
SSD1963 Adapter MCU Parallel Port 5.0 Inch 800x480 STM32 ESP32 Driver Board Capacitive Touch LCD Display
Product Specification:
The product is a 5.0-inch TFT LCD display module, which consists of two parts: 5.0-inch display and ssd1963 adapter board. The display module uses 800x480 resolution, supports rgb565k color display, and uses ssd1963 driver IC. The display module also supports the switching function of capacitive touch screen and resistive touch screen.
| Name | Parameter |
| Display Color | RGB888 16.7M (compatible with rgb5665k) color |
| SKU | MRG5101(no touch), MRG5111(have touch) |
| Screen Size | 5.0(inch) |
| Type | TFT |
| Driver IC | SSD1963 |
| Resolution | 800*480 (Pixel) |
| Module Interface | 8Bit or 16Bit parallel interface |
| Touch Screen Type | Capacitive or Resistive touch screen |
| Touch IC | FT5426(Capacitive touch), XPT2046(Resistive touch) |
| Active Area | 108.00x64.80(mm) |
| Module PCB Size | 121.11x95.24(mm) |
| Operating Temperature | -10ºC~60ºC |
| Storage Temperature | -20ºC~70ºC |
| Input Voltage | 5V |
| IO Voltage | 3.3V |
| Power Consumption | 98mA(The backlight is off), 161mA(The backlight is the brightest) |
| Rough Weight(Net weight) | 133(g) |
Hardware Description:
The appearance of the product is shown in Picture 1 ~ Picture 5
Picture1. Front view of display module
Picture2. Back view of display module Picture3. Front view of adapter board
Picture 4. Back view of adapter board
Picture 5. Combination picture
Picture 6. The module interface and selection circuit
Each identification circuit in Picture 6 is described as follows:
1) --Capacitive touch screen circuit
2) --Resistance touch screen circuit
3) --Disp resistance
4) --P2 interface (Used to connect the adapter board)
5) --P3 interface (Not used)
1) --40pin flexible cable output interface
2) 4) --In line interface of esp32 development board
3) --STM32 development board 32pin flexible cable input interface
5) --STM32 development board 34pin pin input interface
| Number | Pin name | Description |
| 1 | CS | LCD reset control pin( low level enable) |
| 2 | RS | LCD register / data selection control pin(high level: register, low level: data) |
| 3 | WR | LCD write control pin |
| 4 | RD | LCD read control pin |
| 5 | RST | LCD reset control pin( low level reset) |
| 6~21 | D0~D15 | LCD 16 bit data bus pin (use d0 ~ D7 in 8-bit mode) |
| 22 | GND | Module power ground pin |
| 23 | TE | LCD tearing effect signal pin (read only) |
| 24 | NC | No definition, reserved |
| 25 | NC | No definition, reserved |
| 26 | GND | Module power ground pin |
| 27 | GND | Module power ground pin |
| 28 | 5V | Module power supply positive pin (connected to 5V) |
| 29 | TMI | Resistance touch screen SPI bus read data pin (capacitor touch screen not used) |
| 30 | TMO | IIC bus data pin of capacitive touch screen (SPI bus write data pin of resistance touch screen) |
| 31 | PEN | Touch screen interrupt detection pin(Low level when a touch occurs) |
| 32 | NC | No definition, reserved |
| 33 | TCS | Capacitor touch screen reset pin (resistance touch screen chip selection pin) |
| 34 | TCK | IIC bus clock pin of capacitive touch screen (SPI bus clock pin of resistance touch screen) |
| Number | Pin name | Description |
| 1 | TCK | IIC bus clock pin of capacitive touch screen (SPI bus clock pin of resistance touch screen) |
| 2 | TCS | Capacitor touch screen reset pin (resistance touch screen chip selection pin) |
| 3 | PEN | Touch screen interrupt detection pin(Low level when a touch occurs) |
| 4 | TMO | IIC bus data pin of capacitive touch screen (SPI bus write data pin of resistance touch screen) |
| 5 | TMI | Resistance touch screen SPI bus read data pin (capacitor touch screen not used) |
| 6 | 5V | Module power supply positive pin (connected to 5V) |
| 7 | GND | Module power ground pin |
| 8 | GND | Module power ground pin |
| 9 | NC | No definition, reserved |
| 10 | NC | No definition, reserved |
| 11 | TE | LCD tearing effect signal pin (read only) |
| 12~27 | D15~D0 | LCD 16 bit data bus pin (use d0 ~ D7 in 8-bit mode) |
| 28 | RST | LCD reset control pin( low level reset) |
| 29 | RD | LCD read control pin |
| 30 | WR | LCD write control pin |
| 31 | RS | LCD register / data selection control pin(high level: register, low level: data) |
| 32 | CS | LCD reset control pin( low level enable) |
| Number | Pin name | Description |
| 1 | 5V | power pin (connected to 5V) |
| 2 | LCD_RS | LCD register / data selection control pin(high level: register, low level: data) |
| 3 | LCD_RD | LCD read control pin |
| 4 | LCD_D1 | Pin 2 of 8-bit parallel data bus |
| 5 | GND | Power ground pin |
| 6 | LCD_WR | LCD write control pin |
| 7 | LCD_D0 | Pin 1 of 8-bit parallel data bus |
| 8 | LCD_D5 | Pin 6 of 8-bit parallel data bus |
| 9 | LCD_D7 | Pin 8 of 8-bit parallel data bus |
| 10 | LCD_D4 | Pin 5 of 8-bit parallel data bus |
| 11 | LCD_D6 | Pin 7 of 8-bit parallel data bus |
| 12 | LCD_D2 | Pin 3 of 8-bit parallel data bus |
| 13 | TP_CLK | IIC bus clock control pin of capacitive touch screen(SPI bus clock control pin of resistance touch screen) |
| 14 | LCD_D3 | Pin 4 of 8-bit parallel data bus |
| 15 | TP_MISO | SPI bus read data pin of resistance touch screen(capacitive touch screen not used) |
| 16 | LCD_CS | LCD chip select control pin |
| 17 | GND | Power ground pin |
| 18 | LCD_RST | LCD reset control pin |
| 19 | TP_PEN | Touch screen interrupt control pin |
| 20 | TE | Tearing Effect Signal pin(read-only) |
| 21 | TP_CS | Capacitive touch screen reset pin(resistance touch screen chip selection pin) |
| 22 | TP_MOSI | IIC bus data pin of capacitive touch screen(resistance touch screen SPI bus write data pin) |
| 23 | GND | Power ground pin |
| Number | Pin name | Description |
| 1 | VCC5 | Power input pin(connect to 5V) |
| 2 | VCC5 | Power input pin(connect to 5V) |
| 3~10 | R0~R7 | 8-bit RED data pin |
| 11 | GND | power ground pin |
| 12~19 | G0 ~ G7 | 8-bit GREEN data pin |
| 20 | GND | power ground pin |
| 21~28 | B0 ~ B7 | 8-bit GREEN data pin |
| 29 | GND | power ground pin |
| 30 | PCLK | Pixel clock control pin |
| 31 | HSYNC | Horizontal synchronous signal control pin |
| 32 | VSYNC | Vertical synchronous signal control pin |
| 33 | DE | Data enable signal control pin |
| 34 | BL | LCD backlight control pin |
| 35 | TP_CS | Capacitor touch screen reset pin (resistance touch screen chip selection pin) |
| 36 | TP_MOSI | Data pin of IIC bus of capacitance touch screen (write data pin of SPI bus of resistance touch screen) |
| 37 | TP_MISO | Resistance touch screen SPI bus read data pin (capacitance touch screen not used) |
| 38 | TP_CLK | IIC bus clock control pin of capacitive touch screen (SPI bus clock control pin of resistance touch screen) |
| 39 | TP_PEN | Touch screen interrupt control pin (low level when touch is generated) |
| 40 | RST | LCD reset control pin (effective at low level) |
Adapter Board Size:
How to connect the development board:
Packaging & Shipping & Delivery
Packaging Details:
All the products are packed in right way to keep it safe.
For small sizes of products we use tray + carton,
For bigger sizes we use foam slot + carton.
we also design packages according to customers' requirements
Shipping Details:
For small quantity orders: we ship by UPS Air-Express, or DHL/FEDEX/TNT/ EMS Express service, it is safe and fast.
For large quantity orders: we ship by buyer's cargo agent in China,
we can also ship by air or sea transportation by our cargo agent.
Delivery Details:
Ready-made Sample: within 1 week
Custom Sample: 1~2 weeks
Mass production: 3-4 weeks
Our Advantage:
☆Responsibility:
We take all responsibilities for any mistakes what we do make. We will remake all wrong pieces and ship out shortly.
☆Fast response:
Quickly realize your customized ideas, and have a sample ready in short time
☆Free Design:
We offer free design service depending on your ideas, logos, colors, etc.
Good knowledge of the displays market to put together solutions that add value and provide a unique proposition for the client
☆Efficient Communication:
Our sales are all with high English language skills, they are working so hard and efficient.
☆High Quality:
All materials we purchase for making any orders are high quality and RoHS compliant, and Control quality with ISO 9001:2008, ISO 14001:2004 management system.
Advance inspection instrument and equipment to ensure 100% inspection for each and every piece before shipment
☆Quick Delivery (Production Time):
Ready-made Sample: within 1 week
Custom Sample: 1~2 weeks
Mass production: 3-4 weeks
Product Line:
☆ Clean Room class [email protected], Pressurec 0.8kgf
☆ Antistatic floor, resistance : 1x10 ohm to 1x10 ohm
☆ COG production lines: 4 .
☆ Backlight production lines: 2 .
☆ Existing machine capacity will be 1KK per month.
Quality Policy:
All materials we purchase for making any orders are high quality and RoHS compliant, and Control quality with ISO 9001:2008 management system.
Advance inspection instrument and equipment to ensure 100% inspection for each and every piece before shipment
Certification:
FAQ:
Q: How can I get some samples?
A: We don't provide free one, but we can have a discount when you reorder according to different quantity, and you will win at least 3% discount.
Q: What is the MOQ?
A: It depends on different products. Please keep in touch with sales to confirm the MOQ.
Q: How do you control quality?
A: All materials we purchase for making any orders are high quality and RoHS compliant, and Control quality with ISO 9001:2008, ISO 14001:2004 management system.
Advance inspection instrument and equipment to ensure 100% inspection for each and every piece before shipment0*480 CapacitouScreenCDsplay
Q: Does your product have any warranty?
A: Yes, we offer 12 months warranty for our products.
Q: What's your payment method?
A: Payment: T/T, Paypal, Western Union, etc.
For samples: payment in advance.
For mass production: 30% deposit and 70% balance before shipment.
Q: Do you offer custom solution?
A: Yes, we can offer custom solution if standard products couldn't meet buyer' requirements.
Suppliers with verified business licenses
Audited Supplier 
){kind=link}
){kind=link}